Certification
What PED 2014/68/EU certification means for casting buyers
If your castings go into pressure equipment sold in the EU, the Pressure Equipment Directive sets rules for the material and its paperwork. Here is what they mean in practice.
· H.J. MetalCraft technical team

Valve bodies, pump casings and other pressure-retaining castings often end up in equipment sold in the European Union. If they do, the Pressure Equipment Directive 2014/68/EU (PED) applies to the finished equipment, and through it to the materials the equipment is made from. This article explains, in general terms, what that means for the castings you buy. It is not legal advice: your own notified body and the directive's text are the authority.
What the PED asks of materials
The PED applies to pressure equipment with a maximum allowable pressure above 0.5 bar. Annex I, section 4 sets the essential safety requirements for its materials. In short, materials must be suitable for the whole service life: properties, chemical resistance, ageing and suitability for the processes used to make the equipment.
The equipment manufacturer has to show its materials meet these requirements. There are three recognised routes: materials made to a harmonised standard, materials with a European approval for materials (EAM), or a particular material appraisal (PMA) carried out for that equipment.
Material certificates and EN 10204
Annex I, point 4.3 deals with the paperwork. For the main pressure-bearing parts of equipment in categories II, III and IV, the material documentation must take the form of a certificate of specific product control. In practice, that is usually an inspection certificate to EN 10204:
| Document | Who validates it | Based on |
|---|---|---|
| 2.1 Declaration of compliance | The manufacturer | No test results |
| 2.2 Test report | The manufacturer | Non-specific inspection (typical production results) |
| 3.1 Inspection certificate | The manufacturer's authorised inspection representative, independent of manufacturing | Specific inspection of the delivered product |
| 3.2 Inspection certificate | As 3.1, plus the purchaser's or an official third-party inspector | Specific inspection, witnessed by both |
A 3.1 certificate reports the actual results for the product you receive: the heat or cast number, chemical analysis, mechanical test results, heat-treatment condition and any other tests the order called for, such as NDT.
Why the manufacturer's own approval matters
Point 4.3 also says that where a material manufacturer has a quality system certified by a competent body established in the EU, which has made a specific assessment for materials, the certificates that manufacturer issues are presumed to show conformity with the material requirements.
That is what a PED material-manufacturer certificate is. Without it, a buyer may need extra verification of the foundry's certificates before they can go into a PED technical file. With it, the foundry's 3.1 certificates carry that presumption, within the scope the notified body assessed.
What our certificate covers
H.J. MetalCraft holds a certificate from TÜV NORD Systems, Notified Body 0045, for its quality management system for material manufacturers under Directive 2014/68/EU, Annex I, point 4.3 (certificate 0045/202/WZ/22270/24, test specification EN 764-5, section 4.2, valid until August 2027). Its scope is:
- Process: sand castings
- Material classes: ferritic, alloyed, austenitic and austenitic-ferritic (duplex) steel castings
- Range: weight up to 180 kg, wall thickness up to 65 mm
Investment castings and the cast irons are outside that scope. See our certifications page for all three certificates (PED, ISO 9001 and ZED).
What to check when you order
- Is the part inside the scope? Process, material class, weight and section thickness.
- Which document do you need? Say 3.1 or 3.2 to EN 10204 on the purchase order. If you need 3.2, plan the third-party witness at the order stage.
- Which tests go on the certificate? Chemistry and mechanical properties as a minimum; add impact tests, NDT or pressure tests if your design code asks for them.
- How is the part traced? Heat number and marking on the casting should match the certificate. We mark castings with a computerised dot-marking machine and a laser marker.
If you are not sure what your project needs, send the drawing and the design code with your enquiry and we will tell you what we can certify. Our sand casting vs investment casting guide explains why the process choice also affects certification.
Have a casting in mind? Send us the drawing.
Request a quote